AMT Datasouth Accel-7450 Uživatelská příručka

© March 2013, AMT Datasouth Corp. Documax 5380 24-Pin Dot Matrix Printer User’s Guide Document # 131022

- 10 - Connecting the printer to the power source 1. Make sure that the power switch located on the left side of the printer is set to OFF. Press

- 11 - Connecting the printer to the PC Note: The Documax 5380 printer can use a USB, Ethernet, or Serial cable to connect to the PC. Par

- 12 - The interface has a built in feature that will automatically receive transmitted data on any of the port

- 13 - Loading Paper Paper thickness adjustment 1. Adjust the gap lever inside the printer on the front right side to feed thicker paper and forms.

- 14 - 2. Position the paper guide to the furthest right position. 3. Pull tray extension out for long paper/forms requiring extra sup

- 15 - Loading tractor paper 1. Set paper thickness lever, refer to “Loading Paper” section. 2. Set the paper select lever located on the back sid

- 16 - 4. Move the tractor paper guide to the middle of the tractor assembly. 5. Open the tractor covers and place the paper onto th

- 17 - Tractor paper tear off When the printer leaves the factory, the tractor paper tear off function is enabled. At the completion of a print job,

- 18 - Top of form adjustment The top of form setting determines the margin between the top of paper and the first printed line (the top margin). Th

- 19 - Print Driver Installation Win2000 (XP~Vista~Win7) 1. Open the driver folder on the CD shipped with the printer. Then open the subfolder for

- ii - Copyright Declaration Information in this manual is subject to change without notice and does not represent a commitment on the part of AMT Da

- 20 - 8. Right-click on the Documax 5380 icon and select “Printer Properties”. 9. Choose the “Ports” tab and select the correc

- 21 - 7. Click on “Printer maintenance” to access additional printer setup features.

- 22 - 8. Click on “Advance printer setup” to access additional printer setup features.

- 23 - Control Panel Indicator LED’s Basic control panel operations Indicator LED Off On Blink ONLINE (green) —— Lights when the printe

- 24 - Printer settings via printer control panel 1. With ribbon installed, print current settings by pressing the LOAD/EJECT and LF/FF keys while

- 25 - Factory default settings LANGUAGE CHINESE EMULATION OKI CHAR. MODE CHINA FONT SANS SER COURIER PRESTIGE SCR

- 26 - Printer setting definitions Options Description LANGUAGE Specify the printer menu language as English or Chinese. EMULATION Specify printer&a

- 27 - PRINT DIR Select the printing direction of the print head: unidirectional, bidirectional or Auto selected via software. HIGH DENSITY After

- 28 - Ethernet Interface Settings NetFinder search 1. Power on the printer, connect the LAN Ethernet cable to the printer port located on the back

- 29 - Search results: Should the printer not be found during the search, check to see if the network firewall is blocking the sear

- 3 - User Caution... 5 Packaging ..

- 30 - 2. Select the printer information to be modified by clicking on the displayed printer (black frame appears), click “Assign IP” button.

- 31 - 5. Run NetFinder again to verify the printer has been updated with Static IP. 6. Exit NetFinder software. 7. Open the “De

- 32 - Diagnostic Testing ASCII Self-test 1. Power on the printer while pressing the ONLINE key. Pressing the ONLINE key a second time will stop p

- 33 - Interface Specification This Documax 5380 printer can be configured with 2.0 Full-Speed USB interface, RS-232 serial interface, 10/100Base-T E

- 34 - 2. Pin description: 3. Signal description: Typical pin out ~  Input signal: RXD and DSR  Output signal: TXD and DTR

- 35 - When the DTR is low level, the printer is BUSY, it cannot receive the data from HOST. DTR is low level in the following conditions:  The pri

- 36 - Parallel interface 1. Standard Centronics (IEEE1284 NIBBLE) parallel interface connector, DB-36 pin type connector. Signal

- 37 - Printer Maintenance  Cleaning period Periodical cleaning: every six months or every 300 running hours. Cleaning too

- 38 - Printer Specification

- 4 - Diagnostic Testing ... 32 ASCII Self-test .

- 5 - User Caution - 5 -  Unplug this product from the power outlet before cleaning.  Do not use this pro

- 6 - Packaging Unpacking the printer Removing protective material 1. Open the packing box, remove the printer and tear off the

- 7 - Part identification Paper guide Top Cover Power switch Pinch roller assembly Control panel Ribbon cart

- 8 - Installation Installing paper support 1. Open the top cover, align the A, B, C tabs over the printer corresponding A, B, C slots, and then pr

- 9 - Installing the ribbon cartridge 1. Remove ribbon cartridge from the plastic bag. Remove and dispose of ribbon retainers (qty-2).